
QuadroM32x/8L/26x/12Li/26xi Manual II: Administrator's Guide Administrator’s Menus
QuadroM32x/8L/26x/12Li/26xi; (SW Version 5.3.x)
FXO Settings
The FXO Settings are used to configure the FXO support that allows Quadro to connect to other PBXs or analog telephone lines.
The QuadroM8L/26x has 8 FXO lines. For QuadroM32x/8L/26x/12Li/26xi the shared FXO lines are displayed in this page, if available. The shared
FXO lines can be edited from FXO setting page. Any changes applied in that page will be automatically reflected on the FXO gateway(s) that share
its FXO lines.
The FXO Settings allows you to limit incoming or outgoing calls for the selected FXO line if required. Depending on configuration of the FXO
gateways, multiple shared FXO ports from one or more FXO gateways may be available on the QuadroM IP PBXs, thus giving you the option to use
them simultaneously.
The administrator may assign a default recipient for each FXO line where calls from the Central Office (PSTN) will be routed. The assigned recipients
become the Quadro “default users”. If the Quadro Auto Attendant has been selected as a “default user”, a caller from the PSTN needs to go through
the attendant menu to reach the desired extension.
If the FXO service is disabled, the Allowed Call Type, Route Incoming Call to and PSTN number columns are set to “N/A”.
Clicking on the FXO line number will open the FXO Settings
- FXO# page where the FXO line settings may be modified.
The FXO Settings - FXO# page consists of the following
components:
The Enable FXO checkbox selection activates FXO support
for the selected FXO line.
The Allowed Call Type is used to choose the allowed call
directions for the corresponding FXO line. The administrator
may choose between:
• Enabling incoming calls (prohibiting outgoing calls) for
the selected FXO line.
• Enabling outgoing calls (prohibiting incoming calls) for
the selected FXO line.
• Enabling both incoming and outgoing calls for the
selected FXO line.
Fig. II-188: FXO Settings page
The Route incoming FXO Call to manipulation radio
buttons group allows you to define the destination where
incoming calls addressed to the corresponding FXO line will
be forwarded to.
• Extension – this selection allows you to choose the
local PBX user or auto attendant extension to forward
calls. If an inactive extension is chosen from this list, the
voice mail system will answer the call addressed to the
corresponding FXO line. If the Auto Attendant extension
is chosen, it will become the “default user” for the
corresponding FXO line on the Quadro.
Fig. II-189: FXO Line Settings page
• Routing – this selection allows you to forward the incoming calls to the destination defined through Call Routing
. This selection requires you to
enter a routing pattern to the corresponding field. Based on the registered PSTN users, the caller will be able to reach the destination according
to configurations in Call Routing Table.
By choosing a destination, the Quadro administrator virtually assigns a default number that will start ringing when a call is initiated to the Quadro’s
PSTN number.
The PSTN Number text field allows you to enter the PSTN number that the current FXO line is attached to. The field value is optional and used as
an identification parameter for FXO lines. The field value can be left empty.
Alternative AC Termination Mode appears if the local country (Germany, Israel, France, etc.) selected for Quadro has two COs that use different
types of AC termination. Contact your CO to learn about your AC termination mode. Selecting the checkbox may help if the voice quality over FXO is
poor or an echo is noticed.
To modify the FXO Settings
1. Select the FXO line number from the FXO Settings table. The FXO Settings -FXO# will appear where the line settings may be modified.
2. Enable the FXO line to receive calls from the PSTN. To reject calls from/to the PSTN, deselect the Enable FXO checkbox.
3. If FXO has been enabled, select the Call Type from the Allowed Call Type drop down list and the extension from the Route FXO Call to
drop down list to route the FXO calls correspondingly.
4. Insert a PSTN number in the same named text field to identify the FXO line.
5. Enable Alternative AC Termination Mode if this is a requirement of your CO.
6. Press Save to submit the FXO line settings.
Comentarios a estos manuales